NETGEAR FVS318N Firewall Firmware 4.2.0-14

  • 30DOWNLOADS
  • Shareware

    Freeware

  • VIRUS REPORTS

    100%Clean

    virus check results

  • USER RATING

    4.8/5 (625votes)

    vote

  • RUNS ON

    Win7 x64

  • Size

    9.2

  • Updated:

    12-Mar-2014

  • DEVELOPER

    NETGEAR

Description

New features: - Manageability support for NMS200. Bug Fixes: - If sslvpn resource address choose ip address and input Fully Qualified Domain Name then MIB walk ip address is 0.0.0.0,should display. - Fail to walk mib node of syslog. - Many mib nodes in nsysinfo fail to walk the value. - The 6to4 static route can't be recorded in IPv6 route table, so 6to4 tunnel can't work normally. - SNMP process down after create a user in mgsoft. - CLI enhancement for VPN to be inline with reference guide. - [IPv6] After deleting DMZ port RADVD prefix, the DMZ interface IPv6 address about the RADVD prefixes also exist in Router Status page and Detailed Status page. - [CLI]Can not add/modify the static routing in CLI with the interface 'wan'. - Dhcpd process got killed while adding three consecutive IP address in Reserved IPs List in LAN Groups page. - Lan host can not get ip when the reserved ips are consecutive ips. - [IPv6] After deleting DMZ port RADVD prefix, the DMZ interface IPv6 address about the RADVD prefixes also exist in Router Status page and Detailed Status page. - Port number display wrong after modify on ipv6 https management GUI. - IPV4/IPV6 DMZ-WAN outbound block rules do not record logs under view log page. - "Packets Dropped due to IP_MAC Binding violation" should be "0" while there is no ip_mac violation. - [CLI] DMZ-WAN inbound cannot set wan_destination_ip_address to others ip address. - [CLI reference guide] Review feedback for rev11 from QA. - CLI has no the command to configure the 'Wireless logs' in Monitoring->Firewall logs&Email. - Can not capture the packets from dmz port in Diagnostics. - [CLI]Can not set pppoe with static ip in CLI mode. - [CLI,Users]use cli change user type fail. - [CLI] The command "system users idle_timeout " which described in FVS318N CLI reference Guide rev6 cannot be found in CLI. - [CLI] The command "system users password " which described in FVS318N CLI reference Guide rev6 cannot be found in CLI. - [IPv6][DOC]There is wan2 on CLI Reference Guide v9. - [CLI]Can not add/modify the static routing in CLI with the interface 'wan'. - [IPv6]LAN host cannot access wan host ipv6 address with site local address. - [Wireless]if the default profile disable,custom profile enable, the Detailed status and Router Status wireless profile information display error. - There is no info displayed in UPnP portmap tables while making voice connection by MSN. - [CLI] Edit schedule is invalid in some telnet sessions. - [IPSec]:Local ID show error in IKE Policies page. - [IPv6][CLI]Enable lan(ipv6)dhcp server failed. - [CLI]DUT configure the static dns unsuccessfully. - [CLI] Bandwidth profile name can be edit from CLI. - It can apply default outbound policy for ipv6 lan-wan outbound in IPV4 only mode. - [wireless]wireless radio display Channel and Transmit Power not uniform. - [IPV6]Enable Email IP/MAC Violations for ipv6 does not work. - [CLI] lan-wan/dmz-wan inbound/outbound does not need to input dnat_ipaddress/snat address and internal_ip_address also for service any should not ask for translate to port number in Classical Routing mode. - [CLI] Priority and bandwidth items are not displayed in CLI rules list. - [CLI] Schedule time set failed should give a note message to user. - [Wireless]There are no wireless related logs on View Logs page. - The ping result is incorrect when mtu >1466 of pptp or pppoe. - [CLI] DMZ-WAN inbound cannot set wan_destination_ip_address to others ip address. - "Packets Dropped due to IP_MAC Binding violation" should be "0" while there is no ip_mac violation. - [IPv6] When WAN port IPv6 address is static IPv6 address,Secondary DNS Server can be blank. - "Packets Dropped due to IP_MAC Binding violation" should be "0" while there is no ip_mac violation. - IPV4/IPV6 DMZ-WAN outbound block rules do not record logs under view log page. - SIIT can't work normally, When WAN port is down then up. - Can't establish ipv6 vpn tunnel when wan(ipv4) is down and wan(ipv6) is up. - Observed performance degradation over GW-GW VPN tunnel. - Need status radio button for bandwidth profile to enable/disable. Known Issues: - Error prompt information for Edit button in 'Users->Domains'. - PING traffic is not getting stop until we stop and run while blocking ping traffic. - Device is accepting Incoming traffic from one WAN host while lan host is running traffic to multiple wan hosts through port triggering. - Traffic selectors should be any-any by default in add VPN policy page (currently subnet-subnet). - IGMP Proxy behind NAT is not supported. - Device is accepting max 15 bandwidth profiles, below the expected max of 32. - VLAN host is not getting IP when the VLAN profile assigned to port is disabled. - Device WAN IP is showing in ssl-vpn portal URL when user login from LAN side. - XAUTH (CHAP) VPN client tunnel with greenbow clients is not establishing. - Unable to ping through VPN tunnel in Diagnostics page with VLAN subnet as traffic selector. - After Successful connection through WPS PIN method, status message is not correct. - IPV6 Traceroute displays a blank page when trying with domain name. - Device is accepting more than 100 static routes. - Device is accepting static routes when DMZ interface is down. - The device is accepting the multicast mac address in source mac filtering page and lan groups page. - Control sideband drop down list showing wrong information in radio settings page. - GUI is not displaying the message "Administrator privileges are required" when guest user click on the "Up" and "Down" button in firewall rules page. - Disconnect button in IPv6 status page (when WAN is in static) not functioning and connection time is not updating. - Upgrade/downgrade issue in Windows 7 IE9. - Weird logs are coming in DHCP Log page and "Clear Log" button is not working. - Device taking around 15 seconds to display the lan groups page when clicked on it. - DHCP relay functionality is not working across Vlan's until unless once WAN got up. - CLI and GUI dmz mac address is getting displayed in small letters. - [CLI]Getting operation succeeded message after error message for invalid configuration. - Device shows "authentication server1" under domain configuration of CLI, no need of suffix "1" in the end. - [CLI]All groups have asterisks in CLI but not in GUI. - [CLI]spelling mistake in authentication type when we see domains from CLI. - Able to see wireless logs with "local0-wireless" tag and with "kernal -kernal" tag. - [CLI] cannot use CLI to configure IPv6 PPPoE connection. - No data flow through SSL VPN tunnels using IPv6 address on Windows7 client. - SNMP walk "nvpnIpsecVPNTunnelEntry" table, sometimes show the time-out error. - Even disable bandwidth profile, bandwidth limitation still effect network traffic. SharewareABC suggest you to use the most recent driver version. Before install this driver we recommend to set a restore point. This way you can reverse system if the driver is wrong.

Related topics

User Comments( 0 )

Make

submit

Related drivers